Short Description

A four wheeled, rear wheel drive scooter with a long wheel base Designed for outdoor use. Features front and rear lights, a padded high back seat, thumb operated controls, a basket on the front tiller. The seat height is electrically adjustable. Suspension on front and rear. Modesty panel on front tiller and a high / low range switch for speed governance.

Options

Seating
- Sheepskin seat cover

Speed lever
- Accelerator extension lever

Baskets
- seat and rear pole mount

Rear Mounted
- golf bag holder
- crutches holder
- walking frame holder
- oxygen cylinder holder
- Trailer with lockable lid

General Accessories
- visibility flag
- wing mirror
- walking stick clips
- sun canopy
- tarp cover for storage
- trailer with lockable lid

Models

889SEL

Additional Dimensions

Height 1120mm
Range depends on batteries used, terrain and weight of user.

More Details

FRAME: This scooter has fibreglass cowlings, front and rear bumper pads and a slip resistant carpet matting on the footwell. The tiller angle is adjustable and features a modesty panel. The scooter comes standard with a mirror and a full light set.

TRANSPORTING the scooter is facilitated by folding down the tiller, removing the seat and batteries, pulling out the connector pin from main frame and separating front section from rear section.

FREEWHEELING mechanism is operated by a lever situated under the rear cowling next to the right wheel.

BATTERY CHARGING is achieved by connecting the charger provided to a mains power point and plugging it into the scooter at the marked charging terminal on the tiller.

BATTERIES two 28 Amp batteries are stored in separate fibreglass boxes under the seat, held in place with webbing straps.

FRONT & REAR WHEELS are 320mm diameter, pneumatic.

FOOTSPACE is flat with slip resistant matting.

SEAT The seat is a contoured style with vinyl upholstery. It has adjustable head rest, lift up, height adjustable armrests and fold down backrest. Different seat sizes are available.
The seat swivels by lifting a lever located on the right side, under the seat. Seat height is electrically adjustable using a switch located on the tiller below the charging point. The seat is removable by releasing the seat swivel lever and turning the seat to a non locked position and lifting it off. A sliding seat mechanism, activated by turning a lever under the front of the seat, allows the driver to alter seat position while seated.

CONTROLS are a flat, rocker style for acceleration and reverse functions, a speed control knob with max / min indicators, lights to indicate battery status and horn. The scooter is key operated the switch is located on the tiller. The controls are set standard for right hand use, but can be changed by the supplier for left hand use.

BRAKES are electromagnetic.

Factors To Consider

This item should be trialled in the users home environment to ensure maximum safety / independence. Environmental considerations include kerbs, footpaths, road / railway crossings, etc

Overall length.............1300mm
Overall width..............640mm
The space allowed on public transport for carrying mobility equipment is an area of 1300mm by 800mm.

Maintenance

Refer to supplier / manufacturer manual for maintenance details and safety warnings.

Licence & Insurance Requirements

Registration requirements
In NSW, motorised wheelchairs that weigh less than 110 kg and cannot travel at more than 10 km/h do not have to be registered, provided they are being used by a person with mobility problems. A person driving a motorised wheelchair under these circumstances is defined as a pedestrian under the Australian Road Rules and is permitted to travel on a footpath or nature strip adjacent to the road.

Vehicles exempt from registration are covered by the nominal defendant scheme (administered by the Motor Accidents Authority) if they are at fault in an accident in NSW on a road or road-related area and cause injury to another person. However, this cover is only valid in NSW.

Standards

For some types of equipment, specific Australian or other Standard(s) are applicable to the materials used in, the manufacturing processes applied to and the installation of products. Compliance with relevant Standards is indicated by written certification that a product has been tested and assessed as compliant with specified Standards. Purchasers are advised to check with the supplier or manufacturer of this item as to its compliance with relevant Standard(s).

Place Of Manufacture

Taiwan