Short Description
The Easy Travel is a battery operated front wheel drive scooter with twin front wheels. It separates into three components for transport and storage. Padded seat has a folding backrest and armrests. A range of accessories is available. It is intended for indoor and restricted outdoor use on level ground during daylight hours.
Options
. Voltage converter to charge the scooter battery in the car.
. 12 a/h battery
. Scooter cover
. Front basket
. Rear view mirror
. Cane or crutch holder
. Cycle bell
. Drink holder
Models
Only one model is available
| Specification |
Standard |
| Backrest Height |
390 mm |
| Base Height (clearance) |
Unknown |
| Length |
1040 mm |
| Load Capacity (supplier stated) |
114 kg |
| Seat Depth |
450 mm |
| Seat Height |
410 mm from platform; 540 mm from floor |
| Seat Width |
450 mm |
| Weight (kg) |
28 kg |
| Weight of Heaviest Part |
12.9 kg |
| Width |
570 mm |
Additional Dimensions
Height (Min) 860mm
Seat height (fr ground) 540mm
Weight Battery 6kg
More Details
This four wheeled scooter has the two front wheels positioned very close together and therefore behaves similarly to a three wheeled scooter. The scooter will likely have greater manoeuvrability but less stability.
Frame: It is available in three colours, blue, silver and red
Seat: Folding padded seat and back. Does not swivel
Armrests: Lift up
Controls: Finger operated. Tiller top control panel features on / off rocker switch, speed control knob, battery indicator light (LED)
Wheels: Flat free PU 200mm diameter x 50mm wide
Batteries: one 24 volt 7A/H battery
Battery charger: A 24 volt automatic battery charger and basket is supplied.
Freewheeling: rocker switch on / off on tiller
Dismantles: Battery pack, basket
Method of dismantling
1.Remove basket
2.Remove battery at front with handle provided
3.Fold backrest down
4.Lift the ring pull at the side of the footrest platform and at the same time lift the small black lever near the handles and fold handlebars down to connect to cross bar.
6.The scooter can be pulled along using handle bars.
7.To further dismantle the base can be lifted off the tiller.
Factors To Consider
This item should be trialled in the users home environment to ensure maximum safety / independence. Environmental considerations include kerbs, footpaths, road / railway crossings, etc
Overall length............1040mm
Overall width.............860mm
The space allowed on public transport for carrying mobility equipment is an area of 1300mm by 800mm.
State transit will only carry scooters with an unladen weight of less than 200 kg and which can be driven onto the bus, and manoeuvred to fit wholly within the designated wheelchair space under their own power. Any such scooters carried must also comply where relevant with the rules applying to wheelchairs.
Three wheeled mobility aids of any kind are unstable in normal bus operations and will not be carried because of the safety risk.
Accessible buses display a blue and white wheelchair sign on the front of the bus, and on the easy access door.
Maintenance
Refer to supplier / manufacturer manual for maintenance details and safety warnings.
Licence & Insurance Requirements
Registration requirements
In NSW, motorised wheelchairs that weigh less than 110 kg and cannot travel at more than 10 km/h do not have to be registered, provided they are being used by a person with mobility problems. A person driving a motorised wheelchair under these circumstances is defined as a pedestrian under the Australian Road Rules and is permitted to travel on a footpath or nature strip adjacent to the road.
Vehicles exempt from registration are covered by the nominal defendant scheme (administered by the Motor Accidents Authority) if they are at fault in an accident in NSW on a road or road-related area and cause injury to another person. However, this cover is only valid in NSW.
Standards
For some types of equipment, specific Australian or other Standard(s) are applicable to the materials used in, the manufacturing processes applied to and the installation of products. Compliance with relevant Standards is indicated by written certification that a product has been tested and assessed as compliant with specified Standards. Purchasers are advised to check with the supplier or manufacturer of this item as to its compliance with relevant Standard(s).
Place Of Manufacture
Tzora Active Systems Ltd (Israel)
