Short Description

A rear wheel drive scooter with four wheels. The scooter features thumb or finger operated controls, contoured vinyl covered foam seating. It can be customised in terms of speed lever type, seating options, and in built steering column and seat adjustments. A wide range of accessories is available. The scooter is only available in red.

Options

Seating
- adjustable seat
- alternative height seat post
- sheepskin cover
- seat levers on opposite side
Speed Lever
- left hand controls
- right hand controls
Baskets
- seat and rear pole mount
- large basket
- basket cover and lock
General Accessories
- rear vision mirror
- foot retainer
- walking stick clips
- rain coat
- flag
- sun shade
- tyre sealant
Rear Mounted
- crutches holder
- walking frame holder
- oxygen cylinder holder

Models

A three wheel model also available.

Additional Dimensions

Height 990mm
Turning radius 1560mm

More Details

FRAME
epoxy coated steel frame, moulded plastic cowlings, reinforced front nose section for durability and a rear bumper.

SEAT
has a release lever located underneath the front (right hand side) of the seat base and allows the seat to swivel through 180 degrees, locking at 0, 45 and 90 degrees. The backrest angle is adjustable. The armrests pivot up and down. The seat height is fixed.

STEERING COLUMN
can be tilt and height adjusted

FRONT WHEELS
80mm x 255mm pneumatic tyres.

REAR WHEELS
100mm x 255mm pneumatic tyres

BATTERIES
The scooter is powered by two 12 volt, deep cycle, wet batteries which are housed, along with the built in charger, under the seat. The batteries are in separate boxes with carry straps under the seat. The charger point is located above the rear protection strip

BATTERY CHARGING
is achieved by connecting the scooter from the rear charger inlet to a mains power point.

FOOTREST
is a flat platform between the steering column and battery cover. It is covered in non slip, textured matting.

CONTROLS
The programmable controller features on / off key, proportional speed control, horn, hazard lights, indicators, head lights and a battery level indictor.

BRAKES
are electromagnetic

FREEWHEELING
The scooter can be free wheeled by pulling out a lever located at the rear right hand corner of the base.

TRANSPORTING
The scooter can be dismantled into 5 parts for transport - seat, battery cover, batteries and battery boxes, chassis unit, and power pack. Two people are required to dismantle the scooter.

Factors To Consider

This item should be trialled in the users home environment to ensure maximum safety / independence. Environmental considerations include kerbs, footpaths, road / railway crossings, etc

Overall length??????????.1260mm
Overall width??????????..615mm
The space allowed on public transport for carrying mobility equipment is an area of 1300mm by 800mm.

State transit will only carry scooters with an unladen weight of less than 200 kg and which can be driven onto the bus, and manoeuvred to fit wholly within the designated wheelchair space under their own power. Any such scooters carried must also comply where relevant with the rules applying to wheelchairs.

Three wheeled mobility aids of any kind are unstable in normal bus operations and will not be carried because of the safety risk.

Maintenance

All scooters require regular maintenance. Refer to User Manual for specific details.

Licence & Insurance Requirements

In NSW, motorised wheelchairs that weigh less than 110 kg and cannot travel at more than 10 km/h do not have to be registered, provided they are being used by a person with mobility problems. A person driving a motorised wheelchair under these circumstances is defined as a pedestrian under the Australian Road Rules and is permitted to travel on a footpath or nature strip adjacent to the road.

Vehicles exempt from registration are covered by the nominal defendant scheme (administered by the Motor Accidents Authority) if they are at fault in an accident in NSW on a road or road-related area and cause injury to another person. However, this cover is only valid in NSW.

Standards

Specific Australian Standards or other Standard(s) may be applicable for materials, manufacturing processes, or installation of some types of equipment. Compliance with relevant Standards is indicated by written certification that a product has been tested and assessed as compliant with specific Standards. Purchasers are advised to check with the supplier or manufacturer of this item as to its compliance with relevant Standard(s).

Place Of Manufacture

USA