Short Description

A mid wheel drive, steel framed, rigid, powered wheelchair for a child or adult. It is suitable for indoor and outdoor use and is available in a range of seat sizes. It has four interchangeable seating systems with a range of seating options available. A range of other options is available.

Options

. Contoured high back
. Solid seat pan
. Solid tyres
. Lap belt
. Cup holder
. Swing away joystick
. Swing away foot plates
. Elevating legrests
. Oxygen tank holder
. Cane / crutch holder
. Walker holder
. Angle adjustable foot plates

Models

Jazzy 600 - comes with a basic controller.

Additional Dimensions

Overall length 1000mm
Turning circle radius 490mm
Standard seat depth 560mm
Versa seat width 330mm - 530mm
Overall length 895mm
Base weight 55kg
Turning radius 495mm
Max speed up to 8 km/hr
Castors (front) 130mm diameter
Castors (rear) 150mm diameter
Wheels (drive) 355mm diameter
Wheels (anti tip) 150mm diameter
Kerb climbing 75mm

More Details

Suspension
Active Trac ATX suspension incorporates front OMNI castors for enhanced performance over more varied terrain. Mid Wheel 6 technology allows the active front castors to engage, dropping down and making initial contact with the ground, when descending kerbs.

Materials
ABS plastic shroud. Available in two colours - candy apple red or viper blue.

Upholstery
Contoured padded seat and backrest with vinyl on seat, back and armrests

Seat
It comes standard with a grey, vinyl, padded seat and back that lifts off the base.

Footrest
One piece, angle and height adjustable. Optional two piece swing away

Control
The controller is programmable and features flush on / off and mode switches, proportional joystick, speed control, horn and battery level / self diagnostics display.

Brakes
Electronic. Regenerative. Disc Park Brake

Batteries
2 X 12 volt, 55 amp / hr deep cycle batteries
The chair is powered by two 12 volt batteries located within a cartridge style battery box under the frame. The battery charging point is located underneath the controller.

Battery Charger
Off board 7 amp (standard)

Tyres
Pneumatic drive wheels

Castors
OMNI Castors (nylon spherical shaped castors) on front and rear to prevent wheel hang ups. Castors are solid

Anti Tip Wheels
Solid rubber

Freewheeling
The motor can be disengaged and the chair free wheeled by turning levers, located next to each rear wheel, towards the middle of the chair.

Dismantling
Seat is removable. Scooter dismantles to several parts.

Factors To Consider

The space allowed on public transport for carrying mobility equipment is an area of 1300mm by 800mm.

Wheelchair spaces
All new Sydney buses feature special 'kneeling suspension' and a ramp to provide easy access for less mobile passengers.

There are spaces for two wheelchairs on the new buses. These will accommodate most manual and electric wheelchairs with max. length 1250mm, max. width 750mm, max. turning circle1500mm, and max weight 200kg.

For safety reasons, passengers in wheelchairs are advised to face the back of the bus, bracing their wheelchair against the side of the space, applying the brakes and securing the seat belt of the wheelchair.

Wheelchair accessible buses display a blue and white wheelchair sign on the front of the bus, and on the easy access door.

Maintenance

All wheelchairs require regular maintenance. Refer to User Manual for specific details

Licence & Insurance Requirements

In NSW, motorised wheelchairs that weigh less than 110 kg and cannot travel at more than 10 km/h do not have to be registered, provided they are being used by a person with mobility problems. A person driving a motorised wheelchair under these circumstances is defined as a pedestrian under the Australian Road Rules and is permitted to travel on a footpath or nature strip adjacent to the road.

Vehicles exempt from registration are covered by the nominal defendant scheme (administered by the Motor Accidents Authority) if they are at fault in an accident in NSW on a road or road-related area and cause injury to another person. However, this cover is only valid in NSW.

Standards

Specific Australian Standards or other Standard(s) may be applicable for materials, manufacturing processes, or installation of some types of equipment. Compliance with relevant Standards is indicated by written certification that a product has been tested and assessed as compliant with specific Standards. Purchasers are advised to check with the supplier or manufacturer of this item as to its compliance with relevant Standard(s).

Place Of Manufacture

USA